Manual case packing moves only 3–5 cases per minute per worker. The packing table becomes the bottleneck of the whole line.
This guide explains the case packing machine: what it is, the three main types, and how to size it. It helps you pick the right machine.
A case packing machine groups primary packages into a corrugated case. It takes bags, cartons, cans, or bottles from a conveyor and loads them into a case.
The machine then closes the case, or sends it to a case sealer. One machine can pack 15 cases per minute, a typical entry-level speed.
A cartoning machine puts products into folding cartons. A case packing machine puts packed products into corrugated cases.
The two machines sit at different points on the line. Cartoning is primary packaging, and case packing is end-of-line packaging.
A wraparound case packing machine forms the case around the product group. A flat blank feeds from a magazine, folds around the group, and seals with hot melt.
The case fits tightly because it forms to the product, not to a fixed size. A typical wraparound line runs 30–60 cases per minute.
Blanks cost 15–30% less than pre-formed RSC cases above 50,000 cases a month. The saving grows with volume, so high-volume lines gain the most.
A top-load case packing machine drops the product group into a pre-erected case from above. Vacuum cups or grippers lift the group and lower it in.
Top-load suits pouches, bags, and fragile products that cannot take side pressure. A typical top-load line runs 10–40 cases per minute.
The drop height runs 50–200 mm, so fragile products land gently. A typical top-load machine costs $150,000–350,000.
A side-load case packing machine pushes the product group horizontally into an open case. The case sits on its side with flaps open, then turns upright.
Side-load suits rigid products that slide easily, such as cartons, trays, and cans. A typical side-load line runs 15–50 cases per minute.
A typical side-load machine costs $130,000–280,000. It is the fastest choice for uniform rigid products on a compact line.
Size the packer from the upstream output, not from the catalogue top speed. Divide the upstream units per minute by the units in each case.
A filler that runs 120 bottles per minute with 12 bottles per case needs 10 cases per minute. That figure is the floor, not the target.
Add a 15–20% surge factor above the required case rate. The extra speed absorbs short stops and upstream speed swings.
A line that needs 10 cases per minute should run a packer rated at 12. Without the margin, the packer becomes the bottleneck.
Top-load and side-load machines change over in 10–20 minutes with tool-free adjustment. Wraparound machines take 15–40 minutes, a typical range.
Count changeovers per shift before you pick a type. Three or more formats per shift favor the faster-changeover machine.
The RSC 0201 is the standard regular slotted container, the most common case style. It ships flat, erects fast, and seals with tape or hot melt.
Most case packing machines run RSC cases without special tooling. Start with RSC unless the product needs a different case.
The HSC 0200 is a half slotted container with no top flaps. The FOL 0203 is a full overlap container with extra-strong top and bottom.
Both styles suit heavy or tall products that need stronger cases. Check the board grade before you order either style.
A wrap blank is a flat corrugated sheet that folds around the product group. The wraparound machine forms it into a tight case on the line.
Wrap blanks use less board than a pre-formed case of the same size. They suit uniform products that run at high volume.
Lines under 1,500 cases a day suit a top-load or side-load machine. Lines over 2,000 cases a day should look at wraparound first.
Volume decides the architecture, not the brand. Match the machine to the daily count, not to the catalogue.
Count the product formats that run on the line each shift. Three or more formats favor a flexible top-load machine.
A single uniform product favors wraparound speed. Mixed formats favor changeover speed over top speed.
One worker packs 3–5 cases per minute by hand. An entry-level machine packs 15 cases per minute, a typical figure.
The saving is one to two workers per shift on most lines. Count the labour cost across a full year before you order.
LINK Machinery builds case packers for food, pharmaceutical, and chemical lines. Ask LINK for the model that fits your product and case size.
The machines that feed the case packer come from LINK too. The automatic cartoning machine loads products and instruction sheets into cartons. The pillow packaging machine packs biscuits, cookies, and snacks into bags.
Match the packer to the product, not the other way round. Product shape picks the type, volume picks the speed, and case style picks the cost. Talk to LINK Machinery, a CE and RoHS certified China factory, for a case packing machine sized to your line.
1. What is a robotic case packing machine?
A robotic cell uses a delta or articulated robot to pick products and place them in the case. It runs up to 45 cartons per minute, a typical figure. Changeover takes under 5 minutes with digital settings. The robot suits mixed formats and irregular packs that fixed tooling cannot handle.
2. Does a case packing machine need a case erector?
Yes, on most lines. The erector forms empty cases and feeds them to the packer, so the two machines run in sequence. The erector must match the packer speed, or the packer waits for cases. Some lines buy a combined erector-packer frame to save floor space.
3. What is the maximum case weight for a case packing machine?
A top-load or side-load machine handles cases up to 25 kg, a typical limit. A wraparound machine handles up to 20 kg, because the blank rigidity limits heavy loads. Check the case weight with the machine maker before you order a heavy product.
4. How do you test cases from a case packing machine for shipping?
Run ISTA transit testing per ASTM D4169. The test checks drop, vibration, and compression on the packed case. The board needs an ECT rating per TAPPI T811, and a heavier case needs a higher ECT rating.
5. What safety standards apply to a case packing machine?
Guarding follows ANSI/PMMI B155.1 and ISO 12100. The loading area needs interlocked guards, and an e-stop must sit within reach of the operator. The machine must stop at once when a guard opens.
6. Can a case packing machine pack both RSC cases and wrap blanks?
No. RSC packing and wraparound use different architectures, so one machine cannot do both. Pick the case format first, then the machine. A line that needs both formats needs two machines or a change of format.